2026-10-29 · 6 min read
Most saw blade questions arrive in the wrong order. Someone asks whether M42 beats HSS before saying what they're cutting. Or they want the finest tooth they can get, because a fine tooth looks precise.
Neither question can be answered on its own. A blade has to match the section going under it, the machine holding it, and the finish you're willing to pay for. Fix those three and the steel usually picks itself.
Start with the cut, not the blade
Four questions, in this order.
- Solid bar, thick wall, heavy section: coarse pitch, so the tooth has somewhere to put the chip
- Thin wall tube, sheet, small profiles: fine pitch, or you're cutting with teeth straddling air
- Mixed batch, section changing all day: variable pitch, and accept the compromise
- Aluminium, plastic, composite: a different tooth geometry altogether
Then check what the machine can run — blade diameter or band length, arbor, blade width, coolant. Pick the steel last.
What M42 actually buys you
M42 is a molybdenum-series cobalt high-speed steel, cobalt around 8% (typically quoted 7.75–8.75%). You'll find the grade in the high speed tool steel specifications such as ASTM A600.
Cobalt's job is to hold hardness at temperature. It raises hot hardness, which is why cobalt grades tolerate higher cutting speeds than plain high speed steel. That's what you're paying for — not that the blade starts harder on the bench, but that it stays hard once the tooth is hot.
Where that shows up most is the tooth tip. On a bi-metal band the tooth edge is M42 welded to a flexible backing strip. The back has to bend around the wheels, the tip has to cut. Two jobs, two steels, one blade.
We don't quote a single hardness figure for M42, and hardness follows heat treatment more than the grade name anyway. Ask for the certificate with the batch.
Why stainless punishes a dull tooth
Austenitic stainless work-hardens while it's being cut. That's the trap. A tooth that bites and lifts a chip is doing its job. A tooth that rubs hardens the layer underneath it, and the next tooth has to get through that hardened layer instead.
Which is why a stainless job that "needs more pressure" is usually a job with the wrong pitch or a tired blade. Leaning on it makes it worse.
- Keep the chip load up. A tooth that is cutting stays sharp longer than one that is polishing.
- Change the blade when the cut starts to sound different. On stainless a dull blade doesn't only cut slowly, it changes the material it's cutting.
Tooth pitch: the three-to-eighteen rule
One number worth memorising. At least three teeth in the cut, no more than eighteen.
Both ends fail, and they fail differently.
- Too few teeth. The tooth straddles the workpiece instead of loading a chip. The shock snaps teeth, and a broken tooth in the cut usually takes its neighbours with it.
- Too many teeth. The gullet can't clear the chip. Teeth overload, the blade heats, and you strip a run of teeth instead of wearing them out.
On a band saw the working version is: fine for thin wall and small solids, coarse for heavy section, variable pitch when the section keeps changing. Variable pitch alternates coarse and fine spacing so the cut doesn't settle into one rhythm.
Box section and structural are the awkward ones. A heavy box presents two solid faces and two thin walls in the same cut, and no single pitch suits both. You pitch for the face that gives trouble and accept the rest, or you run variable pitch and split the difference.
That's why most of our circular blades are listed with pitch as requested rather than a fixed number. On the 13 mm bi-metal band we stock 10 teeth per inch. On the small pipe discs, tooth count is the more useful figure — the 63 mm and 80 mm discs are quoted at 76 teeth.
Band or circular
Same family of steel, different machine, different economics.
Circular blades suit rigid machines, short cuts and repetition: a chop saw or cold saw cutting bar and tube to length. Diameter and arbor are the fixed numbers, and our M42 circular range runs 20–500 mm diameter on a 6–32 mm arbor, hot-press welded or cold pressed depending on size.
Band blades suit section size. A band reaches a billet that a disc of the same footprint cannot, and the kerf is thinner so less material goes to swarf. The price is the machine, plus a blade that has to be the right length and width for it.
No ranking between them. A shop cutting 20 mm bar all day has no use for a band saw. A shop cutting 300 mm billets shouldn't try it with a 350 mm disc.
Coating is an order option, not a grade
Coatings get listed because buyers ask. A coating doesn't turn plain HSS into M42. Substrate first, coating second.
What the current range carries: TiN, TiAlN and VAPO as coating options on the 350 mm blade — any one of the three, set per order. Ti-coated on several hot-press circular blades. Nitride on the solid M42 circular and on the bi-metal band. TiCN on the 315 mm disc.
Two entries deserve a second look before you order.
- The 315 mm disc is listed with no teeth. It's a toothless disc, so don't order it against a tooth count.
- The 350 mm blade carries three coating options. It isn't one fixed coating, and rainbow isn't a tooth pattern either.
What to send when you ask
A quote request that comes back the same day has five things in it.
- Material and condition — mild steel or stainless, solid, tube or sheet
- Section — diameter or wall thickness, plus the widest and narrowest if it varies
- Machine — blade diameter or band length, arbor, blade width
- Pitch, or the finish you need and let us choose
- Quantity, and whether it repeats
With those, the material question mostly answers itself. Without them we're guessing, and a guessed blade is the expensive kind.
Most circular blades in the range start at two pieces. The small sets and the 13 mm band start at ten. Custom diameters, arbors and tooth counts are ordinary orders here.
Last thing. This is selection guidance, not a specification. The standard and the manufacturer's technical data govern. Use it to narrow the list, then confirm the numbers on the quote.