2026-10-20 · 7 min read
We supply circular and band saw blades in two tooth materials: M42 and plain high-speed steel. The question we are asked most often is whether M42 is worth the difference in price. The honest answer is that it depends on what you are cutting, and the reason comes down to one property.
What M42 actually is
M42 is a molybdenum-series high-speed steel with cobalt, typically around 8%. Plain high-speed steel of the kind used for general-purpose blades carries no cobalt. Both are high-speed steels and both will cut metal; the difference is how they behave at temperature. High-speed steel grades are commonly supplied and checked against ASTM A600, so the designation on a mill certificate is worth reading before you compare prices.
Why heat decides the outcome
A saw tooth does not slice cleanly at the microscopic level — it scrapes, and that work turns into heat at the tooth tip. Once the tip softens, the tooth stops cutting and starts rubbing, and the blade is on its way out. Every sawing problem a buyer describes to us — short blade life, work-hardened stainless, a cut that walks — traces back to heat at the tip.
Stainless steel makes this worse than mild steel for two reasons. It conducts heat poorly, so the heat stays in the cut instead of spreading into the workpiece and the chips. And austenitic grades work-harden: the surface is squeezed and hardens as the tooth passes, so the next tooth meets a harder surface than the last one did. Cutting stainless therefore runs the tooth hotter than cutting low-carbon steel does.
What the cobalt buys
Cobalt raises what the industry calls red hardness — the ability of the steel to hold its hardness while it is hot. That is the whole of the difference between M42 and a plain high-speed-steel tooth, and it is a property of the material rather than a promise about a number of cuts. How much longer one blade lasts than another depends on the material, the section, the speed, the feed and the coolant, and we do not publish a figure for it.
The circular blade forms we stock
| Form | What it is | Where it fits |
|---|---|---|
| Solid M42 | Blade and teeth cut from one piece of M42 | General metal cutting where the blade runs on a rigid machine |
| Hot-press welded, Ti-coated | M42 tooth strip welded to a blade body, with a titanium-based coating | Production cutting where a coated tooth face helps |
| Rainbow finish | M42 blade with a coloured surface finish | Where the finish is specified — confirm the exact coating on the order |
| No-teeth, TiCN finish | Tooth form without a conventional set, with a TiCN finish | Specialised cuts where a conventional tooth form is not wanted |
The rainbow-finished blade is worth a note. Coloured finishes on saw blades can come from more than one coating process, so the appearance alone does not tell you which one you have. If your process depends on a specific coating, state it on the enquiry and we will confirm what the blade is supplied with rather than let you infer it from the colour.
Circular blade or band saw blade
A circular blade suits cut-off work on a rigid machine: short, repeatable cuts, a fixed diameter, and a blade that is cheap to replace when it dulls. A band saw blade suits long stock and heavy sections, because the blade is supported along the whole length of the cut rather than entering the work at one point. We supply both, so the choice is about your machine and your stock rather than about what is available.
Section, width and tooth pitch
Tooth pitch has to match the wall thickness or section you are cutting. Too coarse a pitch and the tooth catches on thin material instead of taking a chip; too fine and the gullets fill with chips and the blade stops clearing the cut. For tube and thin sheet this is the single most common reason a blade fails early. Our band saw range includes a 13 mm width for stainless pipe and sheet, where a narrow blade lets you follow a tighter radius and keep the cut true.
What we hold in this family
- M42 circular blades in solid, hot-press welded with a Ti coating, rainbow finish, and a no-teeth TiCN finish — from 2 pieces.
- M42 bimetal band saw blades, including a 13 mm width for stainless pipe and sheet — from 10 pieces.
- HSS circular blades for metal and pipe, plus a pipe cutting disc.
- A six-piece HSS rotary tool blade set for mixed materials including timber, plastic, fibreglass, copper, aluminium and thin sheet metal.
- A bimetal food-grade machine saw blade spanning M42 high-speed steel and carbon steel, for bone cutting.
Tell us the material, the section and the machine, and we will point you at the form and pitch that suit it. Where a figure is not published for a blade it has been left out rather than filled in from a general reference. This article is a selection guide only — the standard and the manufacturer technical file govern.